Difference between revisions of "Install a hard drive"

From OpenTutorial
Jump to navigation Jump to search
(Added Cleanup template)
(Begining the process of cleanup)
 
Line 1: Line 1:
 
{{cleanup|needs formatting for readability and pre-loaded template cleanup}}
 
{{cleanup|needs formatting for readability and pre-loaded template cleanup}}
 +
 
Attention: read carefully before doing anything. Don't forget to shutdown your computer and to unplug the power cord of it before doing anything, and to plug in the power cord again after everything is done.
 
Attention: read carefully before doing anything. Don't forget to shutdown your computer and to unplug the power cord of it before doing anything, and to plug in the power cord again after everything is done.
  
  
  
Heyo everyone, let's try to create a tutorial. Maybe there will be some language problems but together I hope we can get it.
+
Hello everyone, let's try to create a tutorial. Maybe there will be some language problems but together I hope we can get it.
  
  
A hard drive is a data storage device of computer. Todays computer cannot work without hard drives.
+
A hard drive (HD) is the main data storage device of a computer.
  
The installation of a hard drive consists of two parts.
+
The installation of a hard drive consists of three parts.
  
1) Set it in the box (computer case)
+
# Installation of the HD into the computer's case
2) Make the operating system(s) use it.
+
# Setup and configuration of drivers and or software
 +
# Partitioning and formatting the media
  
  
The first step:
+
== The First Step ==
  
  
1) Get the box open. Maybe you will have to screw out the screws which fix the box door.
+
* Get the case open. Maybe you will have to unscrew the screws which fix the case door.  
2) Look what type is your hard drive of ( (E)IDE or SATA) and look for  corresponding connectors on the mainboard.  If your computer - both  mainboard and power supply unit - supports SATA you will need a free slot and a SATA data cable. Most modern new mainboards support SATA, and if you bought an "upgrade set" with such a mainboard SATA data cables are very probably distributed with it. If your motherboard only supports (E)IDE you need a free slot or rather a free connector on one of IDE data cables. If there are no free slots and, in the case of IDE, no free connectors, you need a free slot for PCI extension cards and an extra hard drive controller as extension card, supporting the hard drive type your hard drive is of. If there are no free slots for hard drive data cables, no free connectors on IDE hard drive data cables and no free slots for extension cards you will not be able to install a hard drive.
+
** Each computer case differs from manufacture to manufacture so you may need to refer to your owner's manual for instructions relating to your particular PC
If there are free slots for SATA, free slots or connectors for (E)IDE look for a power cable for your hard drive. If there are no free power cables you can try using a "multiplier" if you have one but it is not recommended, as your system may become unstable.
+
* Identify your hard drive type.
You will also need a data cable for your hard drive, some screws like what allready installed hard drives have and in the case of IDE maybe one to three jumpers. Look where other hard drives are allready installed - these are 3.5 inch shafts, you need one free 3.5 inch shaft for your hard drive. If there isn't any you can try to install a 3.5 inch (normal) hard drive into a 5.25 inch shaft ( like where your CD/DVD-ROM drive is installed) and fix it there on the right or left border of shaft by screws, but it is better to install the drive into a 3.5 inch shaft.
+
** There are two hard drive types, IDE or SATA
3) If you have all required then put the hard drive into the shaft so you can access the side with connectors for power and data cables, lace it so that you can fix it by screws, fix it by screws, connect the cables to the connectors ofthe hard drive, connect the data cable to the free slot on the motherboard in case of SATA, then get the computer box closed and screwed.
 
 
 
  
------------
+
Look what type is your hard drive of ( (E)IDE or SATA) and look for  corresponding connectors on the mainboard.  If your computer - both  mainboard and power supply unit - supports SATA you will need a free slot and a SATA data cable. Most modern new mainboards support SATA, and if you bought an "upgrade set" with such a mainboard SATA data cables are very probably distributed with it. If your motherboard only supports (E)IDE you need a free slot or rather a free connector on one of IDE data cables. If there are no free slots and, in the case of IDE, no free connectors, you need a free slot for PCI extension cards and an extra hard drive controller as extension card, supporting the hard drive type your hard drive is of. If there are no free slots for hard drive data cables, no free connectors on IDE hard drive data cables and no free slots for extension cards you will not be able to install a hard drive.
Thank you for creating a new tutorial. This text has been pre loaded as a guideline for you to follow. Please replace this and the following texts appropriately, in order to maintain a consistent look and feel for all of OpenTutorial's tutorial pages. This section is to be replaced by the introduction to your tutorial, a brief paragraph explaining the purpose of the tutorial. Place no headings above this paragraph.
 
  
 +
If there are free slots for SATA, free slots or connectors for (E)IDE look for a power cable for your hard drive. If there are no free power cables you can try using a "multiplier" if you have one but it is not recommended, as your system may become unstable.
  
== Heading 1 ==
+
You will also need a data cable for your hard drive, some screws like what allready installed hard drives have and in the case of IDE maybe one to three jumpers. Look where other hard drives are allready installed - these are 3.5 inch shafts, you need one free 3.5 inch shaft for your hard drive. If there isn't any you can try to install a 3.5 inch (normal) hard drive into a 5.25 inch shaft ( like where your CD/DVD-ROM drive is installed) and fix it there on the right or left border of shaft by screws, but it is better to install the drive into a 3.5 inch shaft.
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
+
* If you have all required then put the hard drive into the shaft so you can access the side with connectors for power and data cables, lace it so that you can fix it by screws, fix it by screws, connect the cables to the connectors ofthe hard drive, connect the data cable to the free slot on the motherboard in case of SATA, then get the computer box closed and screwed.
 
 
* Use lists as they help maintain a logical flow to each step in your tutorial
 
** Use sub lists to further organize your content
 
** Use sub lists to further organize your content
 
*** Use sub lists to further organize your content
 
*** Use sub lists to further organize your content
 
** Use sub lists to further organize your content
 
* List item
 
* List item
 
 
 
 
 
# Use lists as they help maintain a logical flow to each step in your tutorial
 
## Use sub lists to further organize your content
 
## Use sub lists to further organize your content
 
### Use sub lists to further organize your content
 
### Use sub lists to further organize your content
 
## Use sub lists to further organize your content
 
# List item
 
# List item
 
 
 
 
 
=== Heading 1_2 ===
 
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
 
 
 
 
 
==== Heading 1_3 ====
 
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
 
 
 
 
 
== Heading 2 ==
 
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
 
 
 
{{adsense2}}
 
 
 
Placing the above ad in a strategic place helps to keep OpenTutorial alive without them I would have a very difficult time paying my hosting costs. As it is right now my current hosting company isn't the greatest. If I can make more money per month by ads I can afford to get a better hosting company and have a better performing website for all.
 
 
 
 
 
=== Heading 2_2 ===
 
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
 
 
 
 
 
== Heading 3 ==
 
Organize your headings so that the maintain a logical and consistent look, separate each heading by two blank lines
 
 
 
 
 
The following sections, Also help OpenTutorial to stay alive (see above). They must be formatted as they are.
 
 
 
To use them just look up a ISBN or ASIN numbers of books and other products offered by www.amazon.com Just enter the numbers and my nifty little ISBN hack will fill in the rest of the information automatically.
 
  
  

Latest revision as of 19:12, 29 June 2009


Attention: read carefully before doing anything. Don't forget to shutdown your computer and to unplug the power cord of it before doing anything, and to plug in the power cord again after everything is done.


Hello everyone, let's try to create a tutorial. Maybe there will be some language problems but together I hope we can get it.


A hard drive (HD) is the main data storage device of a computer.

The installation of a hard drive consists of three parts.

  1. Installation of the HD into the computer's case
  2. Setup and configuration of drivers and or software
  3. Partitioning and formatting the media


The First Step

  • Get the case open. Maybe you will have to unscrew the screws which fix the case door.
    • Each computer case differs from manufacture to manufacture so you may need to refer to your owner's manual for instructions relating to your particular PC
  • Identify your hard drive type.
    • There are two hard drive types, IDE or SATA

Look what type is your hard drive of ( (E)IDE or SATA) and look for corresponding connectors on the mainboard. If your computer - both mainboard and power supply unit - supports SATA you will need a free slot and a SATA data cable. Most modern new mainboards support SATA, and if you bought an "upgrade set" with such a mainboard SATA data cables are very probably distributed with it. If your motherboard only supports (E)IDE you need a free slot or rather a free connector on one of IDE data cables. If there are no free slots and, in the case of IDE, no free connectors, you need a free slot for PCI extension cards and an extra hard drive controller as extension card, supporting the hard drive type your hard drive is of. If there are no free slots for hard drive data cables, no free connectors on IDE hard drive data cables and no free slots for extension cards you will not be able to install a hard drive.

If there are free slots for SATA, free slots or connectors for (E)IDE look for a power cable for your hard drive. If there are no free power cables you can try using a "multiplier" if you have one but it is not recommended, as your system may become unstable.

You will also need a data cable for your hard drive, some screws like what allready installed hard drives have and in the case of IDE maybe one to three jumpers. Look where other hard drives are allready installed - these are 3.5 inch shafts, you need one free 3.5 inch shaft for your hard drive. If there isn't any you can try to install a 3.5 inch (normal) hard drive into a 5.25 inch shaft ( like where your CD/DVD-ROM drive is installed) and fix it there on the right or left border of shaft by screws, but it is better to install the drive into a 3.5 inch shaft.

  • If you have all required then put the hard drive into the shaft so you can access the side with connectors for power and data cables, lace it so that you can fix it by screws, fix it by screws, connect the cables to the connectors ofthe hard drive, connect the data cable to the free slot on the motherboard in case of SATA, then get the computer box closed and screwed.


Bibliography

  • (ISBN 0470043997
  • (ISBN 1591841380
  • (ISBN 020171499X


Amazon's Related Products

  • (ASIN B000MU82WG
  • (ASIN B0009FIS3M
  • (ASIN B000EGMAK8


See Also


External Links